I'm happy to report that the installation of Fedora 9 x86-64 went very smoothly tonight. I yanked down a DVD install from here via torrent. I then burnt an ISO dvd of Fedora 9 using my own instructions here. From the perspective of a Cinelerra advocate, the biggest change from Fedora 7 is that Fedora 9 is more reliant on the ATrpms repository for Cinelerra source code dependencies.
Update 2009/02/15
Since writing this article, I've had very strange crashes and hangs from Cinelerra on Fedora 9. So I've moved on to using Fedora 10 x86-64. The general steps listed below to install Cinelerra still apply, but here's a post that summarizes the steps on how to build Cinelerra from source on Fedora 10, x86-64
*** end update ***
Advice on the Use of Repositories
As a general note, use as few repositories as possible for the various Cinelerra dependencies. Mixing many repos will result in a compile that doesn't work or worse, poor performance or odd behavior in Cinelerra resulting from slightly incompatible libraries. I've lived both and the latter is far worse because you'll spend hours or days pulling your hair out when, in the end, you've got some natty problem that only occurs between this library or that library. Ugh! I get the shivers just thinking about it!
Building Cinelerra from Source?
If you're using Cinelerra on Fedora 9 and want to build Cinelerra from source, here's what you need to do. There will be only three repos needed:
1) Fedora
2) ATrpms
3) Freshrpms (only for mjpegtools)
12/17/2008 NOTE on my strikethrough above
It was brought to my attention that RPM Fusion is the new repository of the repositories for Fedora (a note about Fedora and ATrpms). As I experimented more with my Fedora 9 build, I found an issue with Cinelerra hanging that I will describe in a later post. I fixed the problem by removing the ATrpms dependencies and adding RPMFusion as the only additional Fedora repository.
To reiterate, going forward, I am only using RPM Fusion in addition to Fedora's own repo.
The text below has been updated to reflect this new reality.
end NOTE
There will be only two repos needed:
1) Fedora
2) RPM Fusion
Here are the steps
1) install base Fedora 9 by selecting Office/Productivity and Development tools
2) The set of Cinelerra dependencies will come mainly from the RPM Fusion repository, so add the Fusion repo from here:
http://rpmfusion.org/Configuration
3) In addition to the Fedora repo, you'll now have RPMFusion added as a repository. Use the following script to install core programs for the Cinelerra build. Don't forget to chmod a+x your script!
yum install gsm-devel \
libvorbis* \
libogg* \
libtool* \
libtheora* \
libpng* \
libjpeg* \
libtiff* \
esound* \
audiofile* \
libraw1394* \
libavc1394* \
freetype* \
fontconfig* \
nasm \
e2fsprogs* \
OpenEXR* \
fftw \
fftw-devel \
libsndfile* \
libiec61883* \
libdv* \
libquicktime \
ffmpeg \
xvidcore* \
lame \
lame-devel \
a52* \
faad2* \
x264* \
mjpegtools \
faac*
4) As the Cinelerra CVS source code is no longer available via subversion, install git:
yum install git
Here's a good intro to git
Another good git reference
http://www-cs-students.stanford.edu/~blynn/gitmagic/ch02.html
Here are a couple useful git commands:
To find an earlier version of source code:
git whatchanged --since="20 weeks ago"
To checkout an earlier version of source code:
git checkout [revision number]
example:
git checkout d91e062cadb8a5a7b8c35e9092234948d6918767
5) Grab the Cinelerra CVS source:
git clone git://git.cinelerra.org/j6t/cinelerra.git cinelerra_source
6) Run autogen.sh
[mule@ogre cinelerra_source]# ./autogen.sh
User defined paths to the preferred autoconf and automake versions.
Read the script if you would like to modify them.
AUTOMAKE=automake
ACLOCAL=aclocal
AUTOCONF=autoconf
AUTOHEADER=autoheader
..
7) Run configure
[mule@ogre cinelerra_source]# ./configure
checking build system type... x86_64-unknown-linux-gnu
checking host system type... x86_64-unknown-linux-gnu
checking target system type... x86_64-unknown-linux-gnu
checking for a BSD-compatible install... /usr/bin/install -c
checking whether build environment is sane... yes
checking for a thread-safe mkdir -p... /bin/mkdir -p
checking for gawk... gawk
..
8) Hopefully, configure ran properly and shows that you have all the prerequisites for a build from source:
Summary of mandatory components:
libogg found
libvorbis found
libvorbisenc found
libvorbisfile found
libtheora found
OpenEXR found
libdv found
libpng found
libjpeg libraries found
libjpeg headers found
libtiff libraries found
libtiff headers found
FreeType 2 found
libx264 libraries found
libx264 headers found
libuuid libraries found
libuuid headers found
mjpegtools found
libfftw3 libraries found
libfftw3 headers found
liba52 libraries found
liba52 headers found
libmp3lame libraries found
libmp3lame headers found
libsndfile libraries found
libsndfile headers found
libfaac libraries found
libfaac headers found
libfaad libraries found
libfaad headers found
Summary of optional components:
ESD subsystem found
ESD (Enlightenment Sound Daemon) is enabled
ALSA subsystem found
ALSA is enabled
libraw1394 found
libiec61883 found
libavc1394 libraries found
libavc1394 headers found
librom1394 libraries found
librom1394 headers found
Firewire is enabled
OpenGL 2.0 libraries found
Hardware acceleration using OpenGL 2.0 is enabled
Now type
make
to start compilation.
9) Run "make"
10) Hopefully, there were no errors on make, so run "make install"
11) As the topper, don't forget to install some media players and extra encoding tools!:
yum install avidemux mencoder mplayer transcode audacious vnc
Good luck!
The Mule
Update 2008/11/23
I verified that importing live HDV video from my cam via test-mpeg2 still works. This is done with the following command:
test-mpeg2 -r [node] [file]
end update
No comments:
Post a Comment